PerTronix Flame-Thrower Electronic Ignition Distributor User Manual

1. Úvod

This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600). This distributor is designed to provide enhanced ignition performance for compatible Ford Small Block engines, featuring integrated Ignitor electronic ignition technology for improved reliability and power.

Pred inštaláciou a prevádzkou si pozorne prečítajte tento návod, aby ste zaistili správnu funkciu a bezpečnosť.

2. Bezpečnostné informácie

Vždy dodržiavajte nasledujúce bezpečnostné opatrenia:

• Pred vykonávaním akýchkoľvek elektrických prác odpojte batériu vozidla.
• Noste vhodné osobné ochranné prostriedky (OOP) vrátane ochranných okuliarov a rukavíc.
• Ensure the engine is cool before working on ignition components.
• Keep ignition components away from flammable materials.
• Consult a qualified mechanic if you are unsure about any installation steps.
• Tento produkt obsahuje chemikálie, o ktorých je v štáte Kalifornia známe, že spôsobujú rakovinu a vrodené chyby alebo iné reprodukčné poškodenie. Po manipulácii si umyte ruky.

3. Čo je v krabici

Pred začatím inštalácie skontrolujte, či sú všetky komponenty prítomné:

• PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600)
• Distributor Cap
• Rotor
• Návod na inštaláciu (tento návod)

Image: PerTronix Flame-Thrower Electronic Ignition Distributor with cap, rotor, and wiring visible.

4. Nastavenie a inštalácia

Správna inštalácia je kľúčová pre optimálny výkon. Postupujte podľa týchto krokov:

1. Príprava:
   • Odpojte záporný kábel batérie.
   • Mark the position of the rotor on the old distributor relative to the distributor body, and the position of the distributor body relative to the engine block. This will help with re-timing.
   • Label all spark plug wires before removal.
2. Old Distributor Removal:
   • Remove the distributor cap and spark plug wires.
   • Disconnect any electrical connections to the old distributor.
   • Loosen the distributor hold-down clamp and carefully lift the old distributor out of the engine block. Note the rotation of the rotor as it comes out.
3. New Distributor Installation:
   • Ensure the engine is at Top Dead Center (TDC) on the compression stroke for cylinder #1.
   • Align the new PerTronix distributor's gear with the camshaft gear. The rotor should point to the #1 spark plug terminal on the cap when fully seated. You may need to slightly rotate the rotor or the oil pump drive shaft to engage the gears.
   • Once seated, ensure the distributor body is oriented correctly as marked during removal.
   • Zaistite rozdeľovač pomocou pridržiavača clamp, but do not fully tighten yet to allow for timing adjustments.
4. Pripojenia káblov:
   • The PerTronix Ignitor module has two wires: a red wire and a black wire.
   • Pripojte červený drôt to a switched 12-volt power source that is active when the ignition is in the "ON" and "START" positions. This must be a full 12V source, not a resisted wire.
   • Pripojte čierny drôt to the negative (-) terminal of the ignition coil.
   • Uistite sa, že všetky pripojenia sú čisté a bezpečné.
5. Final Assembly and Timing:
   • Install the new distributor cap and reattach the spark plug wires in the correct firing order.
   • Znova pripojte záporný kábel batérie.
   • Start the engine and use a timing light to set the ignition timing according to your vehicle's specifications.
   • Po nastavení časovania úplne utiahnite prítlačnú skrutku rozdeľovača.amp.

Obrázok: Napramples of Flame-Thrower distributors, illustrating the "Stock Look" and "Billet Plug n' Play" designs. The D134600 is a "Stock Look" model.

5. Návod na obsluhu

The PerTronix Flame-Thrower Electronic Ignition Distributor operates automatically once installed and timed correctly. It replaces traditional points and condenser systems with a maintenance-free electronic module.

• The integrated Ignitor system delivers a consistent, high-energy spark to the spark plugs, improving combustion efficiency.
• The precision timing control ensures stable engine performance across all RPM ranges.
• No adjustments are required for the electronic ignition system itself after initial timing.

6. Údržba

The PerTronix Flame-Thrower Electronic Ignition Distributor is designed for minimal maintenance. Unlike traditional points systems, there are no points to adjust or replace.

• Pravidelná kontrola: Periodically inspect the distributor cap and rotor for cracks, carbon tracking, or excessive wear. Replace if necessary.
• Zapojenie: Check all electrical connections for tightness and corrosion. Ensure wiring is routed away from hot or moving engine components.
• Čistenie: Keep the exterior of the distributor clean and free from oil, grease, and dirt. Use a clean, dry cloth.
• Spark Plugs & Wires: For optimal performance, ensure your spark plugs and spark plug wires are in good condition and are compatible with electronic ignition systems.

7. Riešenie problémov

If you experience issues with your ignition system, consider the following common problems and solutions:

If problems persist after troubleshooting, contact PerTronix technical support.

8. Špecifikácie

9. Záruka a podpora

PerTronix products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official PerTronix webstránky.

For technical support, installation assistance, or warranty claims, please contact PerTronix customer service:

• Webmiesto: www.pertronix.com
• Telefón: Pozrite si webstránka s aktuálnymi kontaktnými číslami.
• When contacting support, please have your product model number (D134600) and purchase information ready.