GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Úvod

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Bezpečnostné informácie

POZOR: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Pred inštaláciou sa uistite, že je istič VYPNUTÝ.
• Toto zariadenie je určené na inštaláciu v súlade s National Electric Code a miestnymi predpismi.
• Do not use in wet locations or where directly exposed to water.
• Len na vnútorné použitie.

Obsah balenia

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Inštalačné skrutky
• Wire Nuts (may vary by package)
• Používateľská príručka (tento dokument)

Nastavenie a inštalácia

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. VYPNITE napájanie: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Odstránenie starého spínača: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Identifikujte vodiče:
   • Linka (horúca): Zvyčajne čierna, vychádzajúca z ističa.
   • Načítať: Usually black, going to the light fixture or appliance.
   • Neutrálne: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Zem: Zvyčajne zelená alebo holá meď.
4. Pripojenie nového prepínača: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Pripojte Linka wire to the terminal marked "LINE".
   • Pripojte Načítať wire to the terminal marked "LOAD".
   • Pripojte Neutrálne wire to the terminal marked "NEUTRAL".
   • Pripojte Ground wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Montážny spínač: Opatrne zatlačte káblový vypínač do nástennej krabice. Upevnite ho dodanými skrutkami.
6. Inštalácia nástennej dosky: Pripevnite novú alebo existujúcu nástennú dosku.
7. Obnoviť napájanie: Znova zapnite napájanie ističom.

Obrázok 1: Predná strana view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Zapojenie Z-Wave (párovanie)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle raz. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Obsluha prepínača

Manuálne ovládanie

• Stlačte tlačidlo top of the paddle to turn the connected load ON.
• Stlačte tlačidlo dno of the paddle to turn the connected load VYPNUTÉ.

Ovládanie Z-Wave

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Údržba

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Čistenie: Na čistenie spínača ho utrite mäkkou handričkouamp plátno. Nepoužívajte abrazívne čistiace prostriedky ani rozpúšťadlá.
• Aktualizácie firmvéru: Skontrolujte GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Všeobecná starostlivosť: Uistite sa, že spínač nie je vystavený nadmernej vlhkosti alebo extrémnym teplotám.

Riešenie problémov

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle raz. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Špecifikácie

Záruka a podpora

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webalebo kontaktujte ich oddelenie služieb zákazníkom.

Webmiesto: www.gocontrol.com

Výrobca: GOCONTROL