1. Úvod
The AUTOOL LM120 Digital Manifold Gauge is an intelligent electronic instrument designed to assist in the installation, testing, and maintenance of refrigeration equipment. This includes systems such as air conditioners, refrigerators, and cold storage units. It provides precise measurements for pressure, temperature, and vacuum, along with advanced diagnostic capabilities.
Image 1.1: AUTOOL LM120 Digital Manifold Gauge in use, connected to an automotive air conditioning system.
2. Bezpečnostné informácie
Pred použitím zariadenia si prečítajte a pochopte všetky bezpečnostné pokyny. Nedodržanie týchto pokynov môže viesť k zraneniu alebo poškodeniu zariadenia.
- Always wear appropriate personal protective equipment (PPE), including safety glasses and gloves, when working with refrigeration systems and refrigerants.
- Ensure adequate ventilation in the work area to prevent the accumulation of refrigerant gases.
- Do not expose the device to extreme temperatures, direct sunlight, or corrosive environments.
- Handle refrigerant hoses and connections with care to prevent leaks and accidental discharge.
- Refer to local regulations and industry standards for the safe handling, recovery, and disposal of refrigerants.
- Do not attempt to repair or modify the device. Contact qualified personnel for service.
3. Produkt skončilview a Komponenty
The LM120 Digital Manifold Gauge features a robust design with an intuitive interface. Familiarize yourself with the components shown below.
Image 3.1: Detailed diagram of the LM120 Digital Manifold Gauge components.
- Háčik
- Clamp-on Temperature Probe Socket
- LCD displej
- Funkčné tlačidlo
- Tlačidlo Run/Stop
- Nulové tlačidlo
- R+/R- Refrigerant Type Selection Buttons
- Tlačidlo stmievania
- Tlačidlo jednotky
- Tlačidlo ° C / ° F
- Tlačidlo napájania
- Nízkotlakový ventil
- Refrigerant Observation Window
- Vysokotlakový ventil
- 1/4 inch Low Pressure Inlet
- Pretlakový ventil
- 1/4 inch High Pressure Inlet
- Refrigerant Inlet / Vacuum Pump Inlet
4. Nastavenie
Before first use, ensure the device is ready for operation.
4.1 Prvé zapnutie
- Stlačte a podržte Tlačidlo napájania (11) zapnite zariadenie.
- The LCD Display (3) will illuminate and show the initial readings.
4.2 Pripojenie hadíc
Connect the appropriate refrigeration hoses to the inlets on the manifold gauge.
- Connect the low-pressure hose to the 1/4 inch Low Pressure Inlet (15).
- Pripojte vysokotlakovú hadicu k 1/4 inch High Pressure Inlet (17).
- Connect the service hose (for vacuum pump or refrigerant tank) to the Refrigerant Inlet / Vacuum Pump Inlet (18).
- Uistite sa, že všetky spoje sú tesné, aby ste predišli úniku.
4.3 Connecting Temperature Probes (Optional)
For dual temperature measurement, connect compatible clamp-on temperature probes (not included) to the Clamp-on Temperature Probe Socket (2).
5. Návod na obsluhu
This section details the various functions and how to operate the AUTOOL LM120.
5.1 Zobrazenie nadview
The large LCD provides clear, real-time data for pressure, temperature, and other parameters.
Image 5.1: The smart digital display provides clear readings for various parameters.
5.2 Výber jednotky
To change pressure or temperature units:
- Stlačte tlačidlo Tlačidlo jednotky (9) to cycle through available pressure units (e.g., Kpa, Psi, Bar).
- Stlačte tlačidlo Tlačidlo ° C / ° F (10) to switch between Celsius and Fahrenheit temperature displays.
5.3 Refrigerant Type Setting
The device has a built-in database of 89 refrigerants. Select the correct refrigerant type for accurate calculations.
Image 5.2: Setting the refrigerant type on the LM120 display.
- Použite R+/R- Refrigerant Type Selection Buttons (7) to scroll through the available refrigerant types.
- Potvrďte svoj výber.
5.4 Meranie tlaku
The LM120 measures both high and low pressures simultaneously.
- Ensure hoses are correctly connected to the high and low-pressure ports of the system.
- The display will show the current high and low pressure readings.
5.5 Meranie teploty
With optional clamp-on temperature probes, the device can measure dual temperatures.
Image 5.3: High/Low pressure temperature test display.
- Attach the temperature probes to the desired measurement points (e.g., suction line, liquid line).
- The display will show T1 and T2 temperature readings.
5.6 Evaporation Pressure & Temperature Test
This function measures the maximum pressure when the refrigerant changes from liquid to gas and the lowest temperature when the liquid becomes gaseous.
Image 5.4: Evaporation pressure and temperature test results on the display.
5.7 Condensing Pressure & Temperature Test
This function measures the minimum pressure when the refrigerant changes from gas to liquid and the maximum temperature when the gas changes to liquid.
Image 5.5: Condensing pressure and temperature test results on the display.
5.8 Pressure Leakage Test
The device can perform a pressure leakage test, recording leak time and speed.
Image 5.6: Pressure leakage test in progress, showing initial and current pressure values over time.
- Connect the gauge to the system to be tested.
- Stlačte tlačidlo Funkčné tlačidlo (4) to navigate to the leakage test mode.
- Follow the on-screen prompts to start and monitor the test. The device calculates the pressure difference between the initial and second test pressures to determine if refrigerant is leaking.
5.9 Meranie vákua
The LM120 can measure the percentage of vacuum achieved in a system.
- Connect the vacuum pump to the Refrigerant Inlet / Vacuum Pump Inlet (18).
- Activate the vacuum pump and monitor the vacuum percentage na displeji.
5.10 Superheat and Subcooling Calculation
Leveraging its integrated 89-type refrigerant database, the LM120 can automatically calculate superheat and subcooling temperatures.
Image 5.7: Built-in database of 89 refrigerant types for accurate calculations.
- Ensure the correct refrigerant type is selected (refer to Section 5.3).
- With pressure and temperature probes connected, the device will display calculated superheat and subcooling values.
6. Údržba
Proper maintenance ensures the longevity and accuracy of your LM120 Digital Manifold Gauge.
- Čistenie: Zariadenie utrite mäkkou, suchou handričkou. Nepoužívajte abrazívne čistiace prostriedky ani rozpúšťadlá.
- Ukladací priestor: Store the gauge in its original case or a protective container in a cool, dry place away from direct sunlight and extreme temperatures.
- Kontrola hadice: Regularly inspect refrigerant hoses for cracks, wear, or damage. Replace damaged hoses immediately.
- Kontrola pripojenia: Ensure all connections and valves are clean and free of debris.
7. Riešenie problémov
If you encounter issues with your LM120, refer to the following common problems and solutions.
| Problém | Možná príčina | Riešenie |
|---|---|---|
| Zariadenie sa nezapne | Low or depleted internal battery; power button not pressed correctly. | Ensure the device is charged or has sufficient power. Press and hold the Power Button firmly. |
| Inaccurate pressure/temperature readings | Incorrect refrigerant selected; loose hose connections; faulty probes; sensor calibration needed. | Verify the correct refrigerant type. Check all hose connections for tightness. Ensure temperature probes are clean and properly connected. Perform a zero calibration if available (using Zero Button). |
| Displej je slabý alebo nečitateľný | Podsvietenie vypnuté; slabá batéria. | Press the Dimming Button (8) to adjust backlight. Ensure the device is charged. |
| Leakage test shows false positive/negative | Improper connection; external temperature fluctuations; insufficient test duration. | Ensure all connections are absolutely leak-free. Conduct the test in a stable environment. Allow sufficient time for the test to complete. |
8. Špecifikácie
Detailed technical specifications for the AUTOOL LM120 Digital Manifold Gauge.
| Funkcia | Špecifikácia |
|---|---|
| Výrobca | AUTOOL |
| Číslo modelu | LM120 |
| Materiál | High-strength Engineering Plastic |
| Rozsah tlakovej skúšky | 0 Kpa – 6000 Kpa |
| Rozlíšenie tlakovej skúšky | 1 Kpa |
| Presnosť tlakovej skúšky | +/- 0.5 %(FS) + 5dgt |
| Limit preťaženia tlakom | 10000 Kpa (10 Mpa; 100 bar) |
| Number of Refrigerants in Database | 89 druhy |
| Štandardné rozhranie | 1/4 palca |
| Rozmery (D x Š x V) | 20.32 x 7.62 x 12.7 cm (8 x 3 x 5 palca) |
| Hmotnosť | 59.53 g (2.1 unce) |
| Vrátane komponentov | 1 set of LM120 Digital Refrigeration Manifold Gauge |
| Vyžadujú sa batérie | No (implies internal rechargeable or power source) |
| UPC | 733810026709, 733810026198 |
9. Záruka a podpora
AUTOOL is committed to providing high-quality products and customer satisfaction.
- Trojročná záruka: For damage caused by non-human factors, AUTOOL promises to resend parts free of charge within 3 years from the date of purchase.
- Permanent Maintenance: The product is covered by permanent maintenance support.
- Zákaznícka podpora: For any inquiries, technical assistance, or warranty claims, please contact AUTOOL customer support. You can expect a response within 24 hours.
