YUHANUS Electric Drop Bolt Lock Instruction Manual

1. Produkt skončilview

The YUHANUS Electric Drop Bolt Lock is designed for use in access control systems, providing enhanced security for various door types. This model operates in NO Mode (Fail-Security), meaning the lock is in a locked state by default when power is off. It will only unlock when power is applied and an authorized signal (e.g., from a push button or remote controller) is received. It features a time delay function for controlled access.

Image 1.1: The YUHANUS Electric Drop Bolt Lock, showcasing its compact design and wiring.

2. Bezpečnostné informácie

• Ensure all power is disconnected before installation or maintenance to prevent electrical shock.
• Installation should be performed by qualified personnel or under professional supervision.
• Overte správny objtage (DC 12V) and current specifications before connecting to a power source. Incorrect voltage môže poškodiť zariadenie.
• Do not expose the lock to excessive moisture or extreme temperatures.
• Vždy dodržiavajte miestne elektrické predpisy a nariadenia.

3. Obsah balenia

Skontrolujte balenie, či sú v ňom všetky položky:

• Electric Mortise Lock Unit
• Kryt panela
• Induction Lock Component
• Mounting Screws (Set)
• Návod na použitie (tento dokument)
• Certifikát zhody

Image 3.1: Contents typically included in the product package, showing the lock units, screws, and a small instruction sheet.

4. Špecifikácie

Image 4.1: Detailed dimensions of the electric drop bolt lock for installation planning.

5. Nastavenie a inštalácia

5.1 Montáž zámku

1. Pripravte si dvere a zárubňu: Identify the desired mounting location on the door frame and the corresponding position on the door for the bolt to engage. The lock is surface-mounted.
2. Označte body vŕtania: Use the lock unit as a template to mark the screw holes on both the door frame and the door.
3. Vŕtacie pilotné otvory: Drill appropriate pilot holes for the mounting screws.
4. Zaistite zámok: Attach the main lock unit to the door frame and the induction lock component to the door using the provided screws. Ensure proper alignment for smooth bolt operation.

5.2 Pokyny na zapojenie

The electric drop bolt lock requires connection to a DC 12V power supply and an access control system. Refer to the wiring diagram below for proper connections.

• Červený kábel: Pripojte sa k +12 V terminal of your power supply control.
• Čierny kábel: Pripojte sa k GND (Ground) terminal of your power supply control.
• Purple Cable: Pripojte sa k NIE (Normally Open) terminal in your power supply control or access control panel. This connection is crucial for the Fail-Security (NO Mode) operation.
• Other Cables: Yellow and White cables are typically for door status feedback (NC/COM), which may or may not be used depending on your access control system's requirements. Consult your access control system manual for these connections.

Image 5.1: Wiring diagram illustrating connections for the electric bolt lock within a typical access control system, including power supply, keypad, and exit button.

6. Návod na obsluhu

6.1 NO Mode (Fail-Security) Operation

This electric drop bolt lock operates in NO Mode (Fail-Security). This means:

• When there is no power, or in case of a power failure, the lock remains in a locked state.
• The lock will only unlock when power is supplied to the lock and an authorized signal is received from the access control system (e.g., pressing a push button, using a remote controller, or entering a code on a keypad).

6.2 Time Delay Function

The lock features an adjustable time delay function, which controls how long the door remains unlocked after an authorized signal is received. The delay can be set to 0 seconds, 3 seconds, or 6 seconds.

To adjust the time delay, locate the small switch or jumper on the side of the lock unit (refer to Image 6.1). Move the switch or adjust the jumpers to select the desired delay setting (0s, 3s, or 6s).

Obrázok 6.1: Detailný záber view of the time delay adjustment switch on the lock unit, allowing selection between 0, 3, and 6 seconds.

7. Údržba

• Čistenie: Wipe the lock's exterior with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the finish or internal components.
• Kontrola: Periodically check all mounting screws to ensure they are tight. Inspect wiring for any signs of wear, fraying, or loose connections.
• Test funkčnosti: Regularly test the lock's operation with your access control system to ensure it locks and unlocks correctly and that the time delay functions as expected.

8. Riešenie problémov

9. Záruka a podpora

For warranty information or technical support, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase for any warranty claims.

Manufacturer: YuHan

Číslo modelu: 769894490600