Inteligentný modul osi Z ATOMSTACK L2
Návod na inštaláciu automatického nastavenia výšky osi Z L2-5W/L2-10W/L2-20W/L2-40W
Poznámka: Obrázky sú len orientačné, pozrite si prosím skutočný produkt. Pre viac informácií naskenujte QR kód.
zoznam
Spôsob inštalácie osi Z
A5 PRO V2/A10 PRO V2
Odskrutkujte 4 ks M4*6 proti smeru hodinových ručičiek, aby ste odstránili posúvač
Nainštalujte vyhradený konektor A5 Pro V2/A10 Pro V2
Utiahnite 4 ks M4*6
A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral A48 PRO/A48 Ultra nie je potrebné premiestňovať koncové spínače
Krok 1
- Prevráťte rytca
- Odstráňte 2 skrutky z dosky koncového spínača
- Posuňte dosku dopredu, aby ste zarovnali 2 otvory
- Zaistite 2 skrutky späť k doske
- Dokončiť
- Prevráťte rytca
Laserová zjednotená metóda inštalácie
Krok: 1 Odstráňte 4 ks M3 a laserový posúvač
Krok: 2 Nainštalujte laserový posúvač pomocou 4 skrutiek M3 odstránených z kroku 1
Poznámka: Odskrutkujte najprv v súprave náradia pripevnite pomocou krížového skrutkovača, potom nainštalujte laserový posúvač na laser A48
Spôsob pripojenia kábla
Spôsob inštalácie lasera
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
A5 PRO V2/A10 PRO V2/A20 PRO V2/A40 PRO V2
Poznámka: Keď je zapnuté, aby ste mohli použiť automatické nastavenie výšky osi Z, na automatické zaostrenie lasera stačí stlačiť tlačidlo „automatické zaostrenie“ na ovládacom paneli
A6 Pro / A12 Pro / A24 Pro / X12 Pro / X24 Pro / E6 Pro / E18 Pro / E24 Pro / A6 Ultral / A12 Ultral / A24 Ultral / X12 Ultral / X24 Ultral
Poznámka: Displej je potrebný pri použití automatického nastavenia výšky osi Z, musíte ho ovládať z konca displeja
- Zákaznícky servis: Pre podrobné záručné podmienky navštívte našu oficiálnu stránku weblokalita : www.atomstack.com Pre technickú podporu a servis pošlite e-mail: support@atomstack.com
- Výrobca: Shenzhen AtomStack Technologies Co.,Ltd
- Adresa: 17th Floor, Building 3A, Phase II, Intelligent Park, No. 76, Baohe Avenue, Bip code: tret, Longgang District, Shenzhen, Guangdong, China
- Naskenujte QR kód: ALEBO čítačka kódov / skener čiarových kódov alebo akákoľvek aplikácia so skenerom
Dokumenty / zdroje
 | L2 Smart modul osi Z |
Referencie
- Používateľská príručkamanual.tools
I have an ATOMSTACK A20 PRO V2 machine and have just purchased a L2 Z axis motorized drive ( BM AAS41A0125-AB ) and would like to hook it up but the cable attached to the unit has a connector which does not match any place on my machine . Where does it go to . In the instructions it looks like where the connection for the y motor is. Please clarify how to hook it up . Thank You Bob
How do I connect the L2 Smart Z-Axis Module cable to an ATOMSTACK A20 PRO V2 machine?
Na pripojenie Inteligentný modul osi Z ATOMSTACK L2 k tvojmu A20 PRO V2, you must use the specific wiring method outlined in the manual for "V2" series machines. The connection does not plug directly into a spare port on the motherboard; instead, it typically involves an adapter or a specific bridge connection.
Podľa Section 05 — Cable connection method for the A20 PRO V2:
If the connector physically does not fit any port on the X-axis carriage board, please verify if your kit included a small doska adaptéra alebo a Y-shaped splitter cable, as some V2 revisions require splitting the signal or using a specific conversion interface provided in the L2 box.
Read the full Q&A page
I don’t know what the transfer board is nor do I see anything on the x axis carriage. What is the x axis terminal ? I don’t see any extra ports anywhere .
Where are the transfer board and X-axis terminal located on the ATOMSTACK L2 Smart Z-Axis Module?
Based on the installation manual for the Inteligentný modul osi Z ATOMSTACK L2, the components you are looking for are part of the cable connection setup (Section 05):
Poznámka: If you do not see extra ports, ensure you are looking at the späť of the laser carriage assembly. On some older models (like the A5 Pro or V2 series), the connection method differs and may involve connecting directly to the main control box or using a specific adapter cable included in the L2 kit. Please verify your specific machine model, as the manual shows different wiring paths for the A5/V2 series versus the Pro/Ultra series.
Read the full Q&A page
I do not see any PCB or any extra ports. Nor is there any adapters or splitters in the box.
Where are the PCB, extra ports, adapters, or splitters for the ATOMSTACK L2 Smart Z-Axis Module?
Based on the ATOMSTACK L2 Smart Z-Axis Module installation guide, the components included in the box (Section 01 - List) are:
Regarding the PCB and Ports: The L2 module is designed to integrate with existing AtomStack frames. For many models (like the A6 Pro, A12 Pro, A24 Pro, etc.), the connection is made directly to the existing X-axis motor interface or the laser module's connection point using the provided Z-axis connection cable. There is typically no separate external PCB board included in this kit.
Regarding Adapters/Splitters: The manual shows that for certain models (Section 05 - Cable connection method), you must unplug the original X-axis motor cable and connect it to the Z-axis module's interface, or use the dedicated connector provided in the kit. If your specific machine model is not listed in the manual (A5, A10, A20, A6 Pro, etc.), you may require a specific adapter not included in the standard L2 package. If these items are missing from your specific kit, it is recommended to contact support@atomstack.com na overenie.
Read the full Q&A page
Now what do I do ?
What are the next steps after installing the ATOMSTACK L2 Smart Z-Axis Module?
Once you have physically mounted the ATOMSTACK L2 Smart Z-Axis Module and connected the cables as shown in the manual, you must configure your software to recognize the new hardware. Follow these steps:
If the module is not moving, double-check that the 2-pin or 4-pin connectors are not reversed and that your machine's firmware is up to date.
>
Read the full Q&A page