MOONS NPSUGMDHB Wireless Node Controller Owner’s Manual

MOONS NPSUGMDHB Wireless Node Controller

Špecifikácie

• Customer’s Part Number:
• MOONS’ Part Number: 4696355000211
• Model: NPSUGMDHB
• P/N: A8768

Zmeny vyhradené bez upozornenia

POPIS

• The Wireless Node Controllers can be installed in the lighting control box, lamp chamber or installed self-contained under eaves or other sheltered areas due to the solid metal enclosure.
• It is very small size and excellent waterproof.
• It can automatically identify different types of LED driver, such as 0-10V, DALI-2/D4i and DMX(RDM).
• Supports 2 channels 0-10V for color temperature adjustment.
• Supports RGBW color.
• Supports dynamic scenes and animations.
• It communicates with the gateway through a WPAN (Sub-GHz).
• Self-building and self-healing MESH Network.
• The sensor interface supports sensor access with digital and analog outputs.

VLASTNOSTI

• Vstupný objemtage:12-30VDC.
• Power consumption: < 1W.
• Wireless communication: IEEE 802.15.4-915MHz.
• Automatically identify dimming mode.
• DMX(RDM) master, up to 6 loads.
• DALI-2/D4i Single-Master Controller, up to 6 loads.
• 2 channels of 0-10V Dimmer, up to 4 loads each channel.
• RGBW color support
• Dynamic scenes and animations
• 1 channel of sensor sample vstup.
• Save several dimming plans.
• Firmware upgrade: OTA.
• Embedded communication encryption mechanism.
• Radio frequency certification: FCC
• Warranty: 5years.

CHARAKTERISTIKY

 ELEKTRICKÉ CHARAKTERISTIKY
At 20 ℃, 50% RH, 100Kpa conditions.

Poznámka:

1. In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.
2. Pri vstupnom objtage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

Prevádzkové podmienky

EMC

Certifikácia

Mechanické údaje

Rozmery
Dimensions are provided in the diagrams above.

Anténa

 Voliteľné príslušenstvo

ŠTÍTOK 

Product barcode information:

• The last 8 digits of SN represent the communication address of the product.
• A” indicates that this product operates in the American frequency band;
• The QR code shows the product’s communication address.

Popis funkcií

Rozhrania

WPAN Module

• Communicate with the Gateway. Transfer various instructions, such as: dimming command, upload power metering data, set parameters and query telemetries accordingly and so on.
• Wireless communication: IEEE 802.15.4-Sub-GHz.
• Embedded communication encryption mechanism.

Stmievanie
Once the device is powered up, it will automatically identify the dimming mode (DALI-2/D4i / DMX(RDM) /0-10V) of the connected load. After recognition, it will automatically report its own running dimming mode and perform necessary operation in this way.

Upozornenie: To achieve perfect recognition of the dimming type, it is recommended that the controller and the LED driver be powered on simultaneously, or the controller be powered on later than the LED driver.

0-10V Stmievanie

• If it is identified as 0-10V dimmer, it can support 2-channel independent 0-10V dimming, which can support adjusting the color temperature (tunable white LED driver and software configuration are required).
• The DIM-TO-OFF LED drivers should be used; the LED drivers’ output will turn off once the dimming voltage je < 0.5 V.
• Support positive and negative logic dimming (configuration required).
• If each channel is connected to multiple LED drivers, the maximum output current of each channel is 10mA, and if the load current is >10mA, the output voltage will be not accurate.

Upozornenie: Pri vstupnom objtage is 12V, 0-10V can output 10V at most; When the output voltage is > 12V, 0-10V can output 11V.

DMX(RDM)

• If identified as a DMX(RDM) master, it can support up to 6 loads (maximum 3 slots for each load) and can be automatically addressed to support RDM instructions.
• 4 loads are recommended.

DALI-2/D4i

• If identified as a DALI-2/D4i Single-Master Controller, up to 6 loads (one address for each load) can be supported, supporting IEC62386-101/103/251/252/253/351 (TYPE D).
• 4 loads are recommended.

Upozornenie:

• At least one of the DALI-2/D4i LED drivers needs to be set to supply power to the DALI bus.
• Maximum of 6 DALI-2/D4i LED Drivers, any DALI-2/D4i LED Drivers >4 will need the power supply disabled
• In the case of DALI-2/D4i mode, the input voltage needs to be higher than the DALI BUS voltage.

Vstup senzora

• 1 channel of sensor input interface.
• Sensors with 0-10V output can be accessed.
• Passive digital output can be accessed.
• Sensors must be configured in software before it is functional in system.

Kontrolky

Upozornenie: 

1.  Purple light indicates that the communication between node controller and LED driver is lost. This might be due to use wrong LED driver or LED driver is not power on or wiring error (for example the reverse connection of the DMX bus). Please check the wiring connection or the power-on status of the LED driver, and then re-power the node controller.

INŠTALÁCIA

For DALI-2/D4i applications with sensor

For DMX(RDM) applications with sensor 

For 0-10V Dim to off applications with sensor 

 For 0-10V Tunable white applications with sensor 

 Recommended installation of antenna interface 

 Recommended installation of M18 Antenna 

OBJEDNÁVKA

Vyhlásenie FCC

Toto zariadenie je v súlade s časťou 15 pravidiel FCC. Prevádzka podlieha týmto dvom podmienkam:

1. Toto zariadenie nesmie spôsobovať škodlivé rušenie a
2. Toto zariadenie musí akceptovať akékoľvek prijaté rušenie, vrátane rušenia, ktoré môže spôsobiť nežiaducu činnosť.

Pozor: Používateľ je upozornený, že zmeny alebo úpravy, ktoré nie sú výslovne schválené stranou zodpovednou za zhodu, môžu zrušiť oprávnenie používateľa prevádzkovať zariadenie.

Poznámka: Toto zariadenie bolo testované a bolo zistené, že vyhovuje limitom pre digitálne zariadenie triedy B podľa časti 15 pravidiel FCC.

Tieto limity sú navrhnuté tak, aby poskytovali primeranú ochranu pred škodlivým rušením pri inštalácii v obytných priestoroch. Toto zariadenie generuje a môže vyžarovať rádiofrekvenčnú energiu a ak nie je nainštalované a používané v súlade s pokynmi, môže spôsobiť škodlivé rušenie rádiovej komunikácie. Neexistuje však žiadna záruka, že pri konkrétnej inštalácii nedôjde k rušeniu. Ak toto zariadenie spôsobuje škodlivé rušenie rádiového alebo televízneho príjmu, čo sa dá zistiť vypnutím a zapnutím zariadenia, používateľovi sa odporúča, aby sa pokúsil napraviť rušenie jedným alebo viacerými z nasledujúcich opatrení:

• Presmerujte alebo premiestnite prijímaciu anténu.
• Zväčšite vzdialenosť medzi zariadením a prijímačom.
• Zapojte zariadenie do zásuvky v inom okruhu, než ku ktorému je pripojený prijímač.
• Požiadajte o pomoc predajcu alebo skúseného rádio/TV technika.

Aby ste zachovali súlad so smernicami FCC o vystavení RF, Toto zariadenie by malo byť inštalované a prevádzkované s minimálnou vzdialenosťou medzi 20 cm od žiariča vášho tela: Používajte iba dodanú anténu.

CUSTOMER’S APPROVAL STAMP
Please sign back after your approval. The specifications will come into force when we receive purchase order.

Zmeny vyhradené bez upozornenia
© 2024 MOONS’. All rights reserved. All content contained herein is subject to change without prior notice. More product documentation and MOONS’ terms and conditions are available at https://www.moonsindustries.com

History Version